Do you find yourself on the lookout for content about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bath tub with a new one is also a moderately hard task. If the old bathtub is easily accessible, the task can relocate easily; if you have to open up a wall to remove the old tub as well as place the new tub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the new one. Ensure you have actually certified on your own for the work and also fit trying it. As opposed to employing a professional to take control of a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have actually already bought a brand-new tub and also don't require to alter the setup of your previous water supply pipelines.
Your tools as well as material list should make up the following:
Getting ready for the Installment
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bathtub till the level checks out level.
To set up taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Turn on the water supply as well as check all joints and new pipework for leakages and tighten them if needed. Fill up the tub as well as also examine the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub needs to wait until the tub has actually been made use of at least once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Safeguard the faucet in place with the manufacturer provided backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, causing the water to pass through the wall between the bathroom and also the tiling, causing complications with moisture and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to enable the movement experienced when the tub is in use. The sealant can break rather very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the market. It is a good idea to fit the floor tiles using water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our topic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking time to read our post. Loved our write up? Please share it. Help someone else find it. I am grateful for your time. Please come visit our blog back soon.
For true quality, dial!